How to Align and Tune-Up Your Table Saw

!±8± How to Align and Tune-Up Your Table Saw

Begin With Your Blade:
It's fairly simple to see when your table saw blade needs to be aligned. Your overall cutting accuracy with suffer and you will likely see burn marks about your cut-lines. You may also experience something not unlike planer snipe where you'll lose a bit more material than intended near the end of your cut.

To remedy said blade alignment issue, that is exactly where you'll want to start - at the blade. First, take a real good look at the thing; after all, the component is pretty darn important to your table saw. Before cleaning, sharpening, or anything else, you'll want to make sure that the blade is totally, completely, perfectly flat. To do this, simply watch the blade come to a stop after disengaging the saw. As the blade slows, it should remain perfectly straight, if there is any wobble in the blade it will have to be replaced. NOTE: A loose blade may also cause a bit of wobble; if you're loose, tighten it up a bit and spin again. If you still wobble after tightening, replace the blade.

If your present blade is flat, you want to also ensure that it is also clean and clear of pitch (a sticky build-up that accrues with each cut). Soaking your blades in oven cleaner is a perfect solution to the pitch issue. Soaking in kerosene or mineral spirits may also do the trick. After soaking wipe or scrub the blade with a non-abrasive cloth to avoid scratches and remember that these solutions are highly flammable. Be always cautious when working with them and always cautious when working with your blades. If you're pitch-free, you may simply wipe the blade with a lint-free cloth and a water-diluted household cleaner.

Ensure also that your blade is sharp; if you have the skill and equipment to sharpen it yourself then that is tremendous, if not, your blade distributor should be able to sharpen it for you for a small fee. If you have any chips, missing teeth, or the blade is in generally bad condition, you should replace it.

Align the Blade to the Miter Slot:
After tightly and properly installing a flat, clean, sharp blade into your saw, make sure the blade is set parallel to the saw's miter slot. To do this, raise the blade as high as possible and pick a specific tooth on the blade as a reference point. You may decide whether or not to mark the tooth. Spin the blade forward until your reference tooth is level with the front end of the saw table and measure and note the distance between your reference tooth to the miter slot. Now, spin the blade in the opposite direction until your reference tooth is level to rear of the saw table and measure and note again. If there is a discrepancy in the distances, adjust the saw motor accordingly (and as per your manual) and repeat the measuring process until you are perfectly lined up. You may also want to ensure that your miter gauge is aligned to the miter slot and can move freely between all positions.

Fence Alignment:
Now check the alignment of the saw's rip fence. Because misalignment of the rip fence can cause kickback, sloppy cutting, and inaccurate angles, this part of the process is particularly important.

By virtue of the blade now being perfectly aligned with the miter slot, you can confidently align the fence to the miter slot as well. Take a framing square or straight-edge that is at least as long as your fence and stand it up inside the miter slot. Slide the fence toward the straight edge until they are firmly pressed together. Closely inspect the space between the fence and straight edge to confirm there are no gaps. Where gaps appear, simply adjust your fence to correct them (see your manual for any further specifics). It is also recommended that you check the fence's locking mechanism to ensure it can brace the pressure of use without sliding.

Square Your Blade to the Saw Table:
To ensure your blade is square to the table, simply set your saw's arbor angle to zero degrees. Using a small framing square or a layout square, ensure the blade forms an exactly ninety degree, or square, angle with the saw table. If you don't find a perfect ninety degree angle, adjust the saw's zero degree stop in the appropriate direction until you obtain a perfect square angle. Specifics for this procedure should also be more completely outlined in the saw's manual.

Inspect Your Throat Plate:
Now that your blade is square and your fence and blade are aligned to the saw's miter slot, you'll want to double check the level of your throat plate. The throat plate should lie at or just below the level of the saw table, if it sits above this level the throat plate may interfere with the stock as it moves toward the blade. To most effectively check the height of the throat plate, slide your framing square or straight edge across it to ensure it doesn't catch. If the plate extrudes past the level of the table, use the adjustment screws on the plate to lower it. As with the blade, check here for cleanliness as well. Saw dust is a retched creature with a tendency to build-up.

How to Align and Tune-Up Your Table Saw

Crosley Turntable Fast

Cooking Made Easy With the Best Electric Range For Your Needs

!±8± Cooking Made Easy With the Best Electric Range For Your Needs

An electric range is actually two appliance rolled into one - a set of electric elements for cooking and an oven. There are three major varieties to choose from:

1. Drop-in
2. Slide-in
3. Freestanding

The selection of the best electric range depends upon your choice based on your requirements and the space available. A great electric range to buy is a slide-in range with a smooth-top cooking surface, although coil elements are available as well. They are available in different sizes and various configurations. It can be as small as 20" or as big as 36" but 30" is most common for ranges.

It should have 4 to 5 radiant elements and a convection oven. A good range should have auto cleaning and a warming drawer. There a number of different additional variations like meat probe, dual radiant baking system, wave touch electronic controls or touch and turn controls, power-boil element, hot surface indicator etc. Some ranges provide an additional storage drawer. Colors available are black, white or stainless steel. Bisque color is also an option.

The top surface can be porcelain or ceramic glass. Many of them are ADA compliant and Star K certified. The additional features like wave touch control is of course provided at an additional price but it is worthwhile to pay. The panel of a slide-in range is unobtrusive but elegant and remains dark. It gets activated with a wave of your hand and lights up when you are cooking a meal.

Some models do have cobalt blue interior and which looks very cool. All the major companies making home appliances are manufacturing electric ovens. Frigidaire, Whirlpool, Electrolux, Kitchen Aid, Sharp, Bosch and GE are the most common brands. The price tag varies depending on the brand you choose and the additional features offered by the model. The starting price can be as low as 0 and the highest price as steep as 00. You should be able select the best electric range for your needs from a wide variety of ranges available.

Cooking Made Easy With the Best Electric Range For Your Needs

Merrick Flossies This Instant Best Prices Paint And Body Shops In Houston Fujitsu S510 Scanner Review

Festool Kapex Sliding Compound Miter Saw Customer Testimonials

!±8± Festool Kapex Sliding Compound Miter Saw Customer Testimonials

Watch this video to hear what customers have to say about Festool power tools.

Festool Kapex Sliding Compound Miter Saw Customer Testimonials

Best Prices Toro 524 Snowblower Braun Battery Toothbrushes Right Now Buy Mid Century Dresser

Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser

!±8± Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser

Brand : Hitachi | Rate : | Price : $512.25
Post Date : Nov 24, 2011 16:45:09 | Usually ships in 24 hours

The Hitachi C10FSH 10-Inch Sliding Dual Compound Miter Saw with Laser Marker provides smooth, accurate miters and crosscuts in a variety of workpieces, including wood, plywood, decorative panels, soft fiberboard, hard board, and aluminum sashes. An ideal tool for trim carpenters, framers, and woodworkers who demand precision and reliability, the C10FSH offers professional-grade performance with its laser marker, dual-bevel cutting action, soft start function, electric brake feature, electronic speed control, and more.

C10FSH Compound Miter Saw Tool Specifications Amps 12 No-Load Speed 3,800 RPM Blade Diameter 10" Arbor Size 5/8" Bevel Angle Range (R & L) 0°-45° Bevel Stops (R & L) 0° and 45° Miter Angle Range Right 0°-57° Left 0°-45° Miter Detent Stops (R & L) 0°, 15°, 22.5°, 31.6° and 45° Tool Height 24-1/4" Weight 43 lbs

The carbon brush and dust-collector bag keep the saw working for the long term.

Make extremely precise cuts with the help of the laser guide. View larger.

Adjust the bevel up to 45 degrees to the left or right. View larger.

Miter scale and thumb-actuated miter stops facilitate simple adjustments at the most common angles. View larger.

Powerful Motor Provides Smooth, Accurate Cuts
The C10FSH Sliding Dual Compound Miter Saw features a powerful 12-amp motor that generates a no-load speed of up to 3,800 RPM for easily making crosscuts and miters in even the toughest workpieces. The electronic speed control ensures consistent RPM throughout the cut, so you get smooth, precise, controlled cuts each and every time.

Additionally, the C10FSH utilizes a Poly-V-Belt transmission rather than a traditional gear transmission. This soft start technology allows the saw to operate smoothly and quietly and reduces recoils during startup.

Compound Feature for Precise Miters and Bevels
Hitachi designed the C10FSH for versatile, easy use. The thumb-actuated positive miter stops allow for simple miter adjustments at the most common angles: 15.0, 22.5, 31.6, and 45.0 degrees to the right or left. The tool also features a 57-degree miter angle to the right and a 45-degree miter angle to the left for maximum flexibility. Additionally, a white-on-black miter scale provides superior visibility, allowing you to easily adjust the angle of the cutting blade for creating miters in crown molding and other trim pieces.

And with a bevel range of 45 degrees to the left and right, you can quickly and easily flip the saw blade while leaving your material in place. To save you even more time, bevel stops to the right and left are conveniently located at zero and 45 degrees.

The 10-inch TCT saw blade (included) makes easy work of trim and other woodwork, and the linear ball-bearing slide system and adjustable pivot fence allow for accurate cutting of large workpieces over 12 inches deep.

Laser Marker Technology for Perfect Cuts Everytime
Hitachi equipped the C10FSH with its exclusive Laser Marker System, which can be activated before the blade is in motion for exact alignment and predictable blade placement. The laser marker is easily adjustable to suit your preferences, simply line up the laser with your mark on the workpiece, and the saw blade will make an exact cut along the laser guide. As long as your measurements are right, your cuts will be, too!

Chock-Full of User-Friendly Features
The C10FSH contains plenty of features to help you make the perfect cut the first time. To start, a splinter guard behind the fence increases safety and reduces tear-out for clean, finished cuts. A patented, fully adjustable chip deflector also prevents tear out, aligns the cutting line, and provide zero-clearance support.

For further refinement, a large table provides a stable guide and sturdy support, a built-in clamping system holds your workpiece in place, a comfortable vertical handle with a vibration-reducing elastomer grip keeps you in control, and an electric brake feature quickly halts the blade to prevent unintended cuts.

The C10FSH also includes a dust collector that minimizes accumulation of dust and particles in your both your workspace and the saw's interior components, keeping your jobsite clean and prolonging the life of the tool. An added bonus, easily accessible carbon brushes will help your saw perform for the long term.

Durably built, this tool is backed with an industry-leading five-year warranty. It is compatible with Hitachi's UU610 Universal Work Station.

About Hitachi: A Tradition of Innovation
Hitachi Power Tools (Hitachi Koki USA, Ltd.) provides professional-grade power tools for a variety of applications, including woodwork, metalwork, concrete, drilling, cutting, and fastening. Hitachi is a leader in power tool research and development and has achieved many firsts in the power tool industry, including creating the first-ever sliding compound miter saw to combine the capacity of a radial arm saw and the convenience of a miter saw. Today, Hitachi continues the tradition of innovation and engineering with new features in addition to classic quality.

What's in the Box
C10FSH 10-Inch Sliding Compound Miter Saw with Laser Marker, 10-inch TCT saw blade, box wrench, dust bag.

Linear ball-bearing slide system helps you cut large workpieces.

• Powerful 10-inch sliding dual compound miter saw with adjustable laser marker, electronic speed control, and soft start to reduce noise and recoil
• 12 amp motor; 3,800 rpm; 10 positive stops for quick settings; pivoting fence to support the work piece
• Stainless steel detent plate; carbide blade
• Includes saw, TCT saw blade, 10-millimeter box wrench, dust bag
• 20-3/4 by 41-1/2 by 24-1/4 inches; 43 pounds; 5-year warranty

Weider Body Works 5000 Free Shipping Buy Harkins Northfield Stapleton Best Buy Bose Am10

Sliding Miter Saw - Ten Inch Or Twelve Inch?

!±8± Sliding Miter Saw - Ten Inch Or Twelve Inch?

A question often asked by prospective sliding miter saw buyers is whether to go for one with a ten inch blade, which will be cheaper, or whether to go all out for a twelve inch machine. In this article you can find out the pros and cons of each.

The first point to make is that we're talking about saw blade diameter when we say "12-inch" or "10-inch" etc. With a non-sliding miter saw, there is a direct relationship between the blade size and the maximum cut size, but with a sliding miter saw it's not quite the same because of course the slider extends the cut length. However, even taking that into account, a twelve inch saw is going to be able to make longer cuts because, basically, everything tends to be built bigger.

Indeed, it's not just the length of cut that's bigger with a twelve inch saw. The depth is also greater because the machine designers have that extra blade surface area to play with. For some people this extra depth capacity alone makes the twelve inch a necessity.

On the other hand, many people find that a ten inch sliding miter saw is big enough for 95% of jobs around the home, including all the obvious things like decking and crown molding. This means it can be hard to justify the extra expense of a twelve inch sliding miter saw; and we're talking maybe an extra 0 or 0 in cost; just to cope with the 5% of projects that the ten inch saw can't handle.

Something else to mention is that if you think the ten inch saw won't cope with bigger cross-cuts, remember that a table saw rather than a sliding miter saw is really the tool of choice for big cross-cuts. So, if that's the main reason you would need a twelve inch miter saw, I would get a ten inch saw and then think about buying a table saw to go with it. This combination will give you a great deal of flexibility and you will be able to use exactly the right tool for the job in hand.

Let's face it, however big a machine you get, there is always going to be some job sooner or later that it will not cope with, so for most people a compromise that handles 95% of the work is about right. The problem is that this 95% will comprise different things for different people. If you regularly make wide shelves, or if you need to cut, say, six-inch crown molding on a regular basis, then a ten inch sliding miter saw is just not going to work for you.

Personally, I try to predict what work I will need to do over the next year or so and buy a saw that will cope with the 95% benchmark. Anything more and the price cannot really be justified.

Sliding Miter Saw - Ten Inch Or Twelve Inch?

Airtight Containers Buy Online